Sponsored Links

Selasa, 09 Januari 2018

Sponsored Links

KN 62A - BendixKing
src: www.bendixking.com

Distance measuring equipment (DME) is a transponder-based radio navigation technology that measures slant range distance by timing the propagation delay of VHF or UHF radio signals.

Developed in Australia, it was invented by James "Gerry" Gerrand under the supervision of Edward George "Taffy" Bowen while employed as Chief of the Division of Radiophysics of the Commonwealth Scientific and Industrial Research Organisation (CSIRO). Another engineered version of the system was deployed by Amalgamated Wireless Australasia Limited in the early 1950s operating in the 200 MHz VHF band. This Australian domestic version was referred to by the Federal Department of Civil Aviation as DME(D) (or DME Domestic), and the later international version adopted by ICAO as DME(I).

DME is similar to secondary radar, except in reverse. The system was a post-war development of the IFF (identification friend or foe) systems of World War II. To maintain compatibility, DME is functionally identical to the distance measuring component of TACAN.


Video Distance measuring equipment



Operation

Aircraft use DME to determine their distance from a land-based transponder by sending and receiving pulse pairs - two pulses of fixed duration and separation. The ground stations are typically collocated with VORs or ILS systems. A low-power DME can be collocated with an ILS glide slope antenna installation where it provides an accurate distance to touchdown function, similar to that otherwise provided by ILS marker beacons.

A typical Distance measuring equipment ground transponder system for en-route or terminal navigation will have a 1 kW peak pulse output on the assigned UHF channel.



Maps Distance measuring equipment



Hardware

The DME system comprises a UHF transmitter/receiver (interrogator) in the aircraft and a UHF receiver/transmitter (transponder) on the ground.


Laser Distance Meter, Laser Distance Measurer, Laser Measuring Tape
src: www.stanlay.in


Timing

SEARCH MODE: 150 interrogation pulse-pairs per second.

The aircraft interrogates the ground transponder with a series of pulse-pairs (interrogations) and, after a precise time delay (typically 50 microseconds), the ground station replies with an identical sequence of pulse-pairs. The DME receiver in the aircraft searches for reply pulse-pairs (X-mode= 12 microsecond spacing) with the correct interval and reply pattern to its original interrogation pattern. (Pulse-pairs that are not coincident with the individual aircraft's interrogation pattern e.g. not synchronous, are referred to as filler pulse-pairs, or squitter. Also, replies to other aircraft that are therefore non-synchronous also appear as squitter).

TRACK MODE: less than 30 interrogation Pulse-pairs per second, as the average number of pulses in SEARCH and TRACK is limited to max 30 pulse pairs per second.

The aircraft interrogator locks on to the DME ground station once it recognizes a particular reply pulse sequence has the same spacing as the original interrogation sequence. Once the receiver is locked on, it has a narrower window in which to look for the echoes and can retain lock.


handheld 60M laser distance meter cp 60 diastimeter Distance ...
src: ae01.alicdn.com


Distance calculation

A radio signal takes approximately 12.36 microseconds to travel 1 nautical mile (1,852 m) to the target and back--also referred to as a radar-mile. The time difference between interrogation and reply, minus the 50 microsecond ground transponder delay, is measured by the interrogator's timing circuitry and converted to a distance measurement (slant range), in nautical miles, then displayed on the cockpit DME display.

The distance formula, distance = rate * time, is used by the DME receiver to calculate its distance from the DME ground station. The rate in the calculation is the velocity of the radio pulse, which is the speed of light (roughly 300,000,000 m/s or 186,000 mi/s). The time in the calculation is (total time - 50µs)/2.


DME
src: i.ytimg.com


Accuracy

The accuracy of DME ground stations is 185 m (±0.1 nmi). It's important to understand that DME provides the physical distance from the aircraft to the DME transponder. This distance is often referred to as 'slant range' and depends trigonometrically upon both the altitude above the transponder and the ground distance from it.

For example, an aircraft directly above the DME station at 6,076 ft (1 nmi) altitude would still show 1.0 nmi (1.9 km) on the DME readout. The aircraft is technically a mile away, just a mile straight up. Slant range error is most pronounced at high altitudes when close to the DME station.

Radio-navigation aids must keep a certain degree of accuracy, given by international standards, FAA, EASA, ICAO, etc. To assure this is the case, flight inspection organizations check periodically critical parameters with properly equipped aircraft to calibrate and certify DME precision.

ICAO recommends accuracy of less than the sum of 0.25 nmi plus 1.25% of the distance measured.


Aliexpress.com : Buy CSS Laser Rangefinder Distance Measuring ...
src: ae01.alicdn.com


Specification

A typical DME transponder can provide distance information to 100 to 200 aircraft at a time. Above this limit the transponder avoids overload by limiting the sensitivity of the receiver. Replies to weaker more distant interrogations are ignored to lower the transponder load.


Amazon.com: Sunwin 48mm-77mm Optical Digital Pupillary Distance ...
src: images-na.ssl-images-amazon.com


Radio frequency and modulation data

DME frequencies are paired to VHF omnidirectional range (VOR) frequencies and a DME interrogator is designed to automatically tune to the corresponding DME frequency when the associated VOR frequency is selected. An airplane's DME interrogator uses frequencies from 1025 to 1150 MHz. DME transponders transmit on a channel in the 962 to 1213 MHz range and receive on a corresponding channel between 1025 and 1150 MHz. The band is divided into 126 channels for interrogation and 126 channels for reply. The interrogation and reply frequencies always differ by 63 MHz. The spacing of all channels is 1 MHz with a signal spectrum width of 100 kHz.

Technical references to X and Y channels relate only to the spacing of the individual pulses in the DME pulse pair, 12 microsecond spacing for X channels and 30 microsecond spacing for Y channels.

DME facilities identify themselves with a 1,350 Hz Morse code three letter identity. If collocated with a VOR or ILS, it will have the same identity code as the parent facility. Additionally, the DME will identify itself between those of the parent facility. The DME identity is 1,350 Hz to differentiate itself from the 1,020 Hz tone of the VOR or the ILS localizer.


handheld 60M laser distance meter cp 60 diastimeter Distance ...
src: ae01.alicdn.com


Terminal DME

A terminal DME, referred to as a TDME in navigational charts, is a DME that is designed to provide a 0 reading at the threshold point of the runway, regardless of the physical location of the equipment. It is typically associated with ILS or other instrument approach.


Electronic Rangefinder, Electronic Rangefinder Suppliers and ...
src: sc01.alicdn.com


Future

DME operation will continue and possibly expand as an alternate navigation source to space-based navigational systems such as GPS and Galileo.




See also

  • Global Positioning Satellite (GPS)
  • Instrument flight rules (IFR)
  • Transponder landing system (TLS)
  • Instrument landing system (ILS)
  • Non-directional beacon (NDB)
  • Tactical Air Navigation (TACAN)
  • VHF omnidirectional range (VOR)
  • Squitter
  • Gee-H (navigation)



References




External links

  • DME Basics
  • UK Navaids Gallery with detailed Technical Descriptions of their operation
  • Flash based instrument simulator with DME
  • U.S. National Aviation Handbook for the VOR/DME/TACAN Systems
  • ICAO Annex 10 Volume 1 International Standards & Recommended Practices

Source of the article : Wikipedia

Comments
0 Comments