Braking distance

src: thumbs.dreamstime.com

Braking distance refers to the distance a vehicle will travel from the point when its brakes are fully applied to when it comes to a complete stop. It is primarily affected by the original speed of the vehicle and the coefficient of friction between the tires and the road surface, and negligibly by the tires' rolling resistance and vehicle's air drag. The type of brake system in use only affects trucks and large mass vehicles, which cannot supply enough force to match the static frictional force.

The braking distance is one of two principal components of the total stopping distance. The other component is the reaction distance, which is the product of the speed and the perception-reaction time of the driver/rider. A perception-reaction time of 1.5 seconds, and a coefficient of kinetic friction of 0.7 are standard for the purpose of determining a bare baseline for accident reconstruction and judicial notice; most people can stop slightly sooner under ideal conditions.

Braking distance is not to be confused with stopping sight distance. The latter is a road alignment visibility standard that provides motorists driving at or below the design speed an assured clear distance ahead (ACDA) which exceeds a safety factor distance that would be required by a slightly or nearly negligent driver to stop under a worst likely case scenario: typically slippery conditions (deceleration 0.35g) and a slow responding driver (2.5 seconds). Because the stopping sight distance far exceeds the actual stopping distance under most conditions, an otherwise capable driver who uses the full stopping sight distance, which results in injury, may be negligent for not stopping sooner.

Video Braking distance

Derivation

Energy equation

The theoretical braking distance can be found by determining the work required to dissipate the vehicle's kinetic energy.

The kinetic energy E is given by the formula:

${\displaystyle E={\frac {1}{2}}mv^{2}}$,

where m is the vehicle's mass and v is the speed at the start of braking.

The work W done by braking is given by:

${\displaystyle W=\mu mgd}$,

where ? is the coefficient of friction between the road surface and the tires, g is the gravity of Earth, and d is the distance travelled.

The braking distance (which is commonly measured as the skid length) given an initial driving speed v is then found by putting W = E, from which it follows that

${\displaystyle d={\frac {v^{2}}{2\mu g}}}$.

The maximum speed given an available braking distance d is given by:

${\displaystyle v={\sqrt {2\mu gd}}}$.

Maps Braking distance

Newton's Law and Equation of Motion

From Newton's second law:

${\displaystyle F=ma}$

For a level surface, the frictional force resulting from coefficient of friction ${\displaystyle \mu }$ is:

${\displaystyle F_{frict}=-\mu mg}$

Equating the two yields the deceleration:

${\displaystyle a=-\mu g}$

The ${\displaystyle d_{f}(d_{i},v_{i},v_{f})}$ form of the formulas for constant acceleration is:

${\displaystyle d_{f}=d_{i}+{\frac {v_{f}^{2}-v_{i}^{2}}{2a}}}$

Setting ${\displaystyle d_{i},v_{f}=0}$ and then substituting ${\displaystyle a}$ into the equation yields the braking distance:

${\displaystyle d_{f}={\frac {-v_{i}^{2}}{2a}}={\frac {v_{i}^{2}}{2\mu g}}}$

src: www.cycleworld.com

Total stopping distance

The total stopping distance is the sum of the perception-reaction distance and the braking distance.

${\displaystyle D_{total}=D_{p-r}+D_{braking}=vt_{p-r}+{\frac {v^{2}}{2\mu g}}}$

A common baseline value of ${\displaystyle t_{p-r}=1.5s,\mu =0.7}$ is used in stopping distance charts. These values incorporate the ability of the vast majority of drivers under normal road conditions. However, a keen and alert driver may have perception-reaction times well below 1 second, and a modern car with computerized anti-skid brakes may have a friction coeficient of 0.9--or even far exceed 1.0 with sticky tires.

Experts historically used a reaction time of 0.75 seconds, but now incorporate perception resulting in an average perception-reaction time of: 1 second for population as an average; occasionally a two-second rule to simulate the elderly or neophyte; or even a 2.5 second reaction time--to specifically accommodate very elderly, debilitated, intoxicated, or distracted drivers. The coefficient of friction may be 0.25 or lower on wet or frozen asphalt, and anti-skid brakes and season specific performance tires may somewhat compensate for driver error and conditions. In legal contexts, conservative values suggestive of greater minimum stopping distances are often used as to be sure to exceed the pertinent legal burden of proof, with care not to go as far as to condone negligence. Thus the reaction time chosen can be related to the burden's corresponding population percentile; generally a reaction time of 1 second is as a preponderance more probable than not, 1.5 seconds is clear and convincing, and 2.5 seconds is beyond reasonable doubt. The same principle applies to the friction coefficient values.

Actual total stopping distance

The actual total stopping distance may differ from the baseline value when the road or tire conditions are substantially different from the baseline conditions or when the driver's cognitive function is superior or deficient. To determine actual total stopping distance, one would typically empirically obtain the coefficient of friction between the tire material and the exact road spot under the same road conditions and temperature. They would also measure the person's perception and reaction times. A driver who has innate reflexes, and thus braking distances, that are far below the safety margins provided in the road design or expected by other users, may not be safe to drive. Most old roads were not engineered with the deficient driver in mind, and often used a defunct 3/4 second reaction time standard. There have been recent road standard changes to make modern roadways more accessible to an increasingly aging population of drivers.

src: i.ytimg.com

See also

• Assured Clear Distance Ahead
• Brake
• Cadence braking
• Skid mark
• Stopping sight distance
• Threshold braking
• Vehicle metrics
• Vehicular accident reconstruction

src: blog.esurance.com

Notes

src: lallouslab.net

References

Further reading

• B. Finberg (2010). "Judicial notice of drivers' reaction time and of stopping distance of motor vehicles traveling at various speeds". American Law Reports--Annotated, 2nd Series. 84. The Lawyers Co-operative Publishing Company; Bancroft-Whitney; West Group Annotation Company. p. 979. 
• E. Campion (2008). "Admissibility in evidence, in automobile negligence action, of charts showing braking distance, reaction times, etc.". American Law Reports--Annotated, 3rd Series. 9. The Lawyers Co-operative Publishing Company; Bancroft-Whitney; West Group Annotation Company. p. 976. 
• C. C. Marvel (2012). "Admissibility of experimental evidence, skidding tests, or the like, relating to speed or control of motor vehicle". American Law Reports--Annotated, 2nd Series. 78. The Lawyers Co-operative Publishing Company; Bancroft-Whitney; West Group Annotation Company. p. 218. 
• Jerre E. Box (2009). "Opinion testimony as to speed of motor vehicle based on skid marks and other facts". American Law Reports--Annotated, 3rd Series. 29. The Lawyers Co-operative Publishing Company; Bancroft-Whitney; West Group Annotation Company. p. 248. 
• Wade R. Habeeb (2008). "Negligence of driver of motor vehicle as respects manner of timely application of proper brakes". American Law Reports--Annotated, 2nd Series. 72. The Lawyers Co-operative Publishing Company; Bancroft-Whitney; West Group Annotation Company. p. 6. 

src: i.ytimg.com

External links

• Car Stopping Distance Calculator
• Braking Distance Calculator
• Tables of speed and stopping distances
• Wikibooks: Sight Distance

Source of the article : Wikipedia